Bike Equipment

Holds stainless steel stay rods to fender Contains: - (1) Eyelet bolt - (1) 10mm lock nut - (1) Rubber cap Compatibility: - All Hardcore, SpeedEZ, Cascadia, Cascadia ALX, & Grasshopper fenders

Compatible with: - Hardcore bike fenders - 700c x 45mm - Full bike fenders - 700c x 45mm - SpeedEZ bike fenders - 700c x 45mm - Hardcore Recumbent bike fender - 700c rear - Contains 45mm rear fender plastic clip, fork and brake bridge thru bolts, stay bolts and lock washers

Compatible with: - Full bike fenders - 26" x 60mm - SpeedEz bike fenders - 26" x 60mm - Hardcore bike fenders - 26" x 60mm - Contains 60mm rear fender plastic clip, fork and brake bridge thru bolts, stay bolts and lock washers

The Hardcore Fender Hardware Kits are compatible with select Hardcore fenders, Full Fenders, Hardcore Recumbent Fenders, and SpeedEZ fenders. Includes: - Rear fender plastic clip - Fork and brake bridge-thru bolts - Stay bolts and lock washers Specific compatibility w/Planet Bike fenders: - 35mm Width: 700c x 35mm Fenders (Hardcore) - 45mm Width: 700c x 45mm (Hardcore, Full, and SpeedEZ); 700c Rear (Hardcore Recumbent) - 60mm Width: 26-inch x 60mm (Full, SpeedEZ, and Hardcore)

- Contains 2 Mudflaps and Quick-Snap Attachments - Compatible with all hybrid (45mm) fenders (part#s 7004, 7006, 7013, 7015) (sold separately) - For use with 45mm width fenders (sold separately)

Topeak's MTX DeFender is the perfect addition to your RX BeamRack. It clips seamlessly to the rack and provides valuable protection against moisture and trail grime.

- Releases front fender stays if debris is present in between fender and tire - Fits current and past Grasshopper, Cascadia ALX, Cascadia and Hardcore front fenders (not recommended for non-Planet Bike fenders)

- Simplistic safety light designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries - Lumens: 6

Others out on the roads and paths will see you when Sunlite's TL-L340 Taillight is on your bike. It sports 3 bright LEDs, steady and flashing modes, and a long run time.

•Steel •Chrome Plated •Front or Rear •Cruiser •26-inch x 75mm

- The seat bag alternative - Stash your stuff at a lower center of gravity - Two convenient size options, small or large

- Rubber straps - Fit Raceblade, Mud-x - Set of 8

Put it on your seatpost, put it on your seatstay, put it anywhere—Sunlite's Griplite goes everywhere. This powerful little light boasts two LEDs and runs for a whopping 100 hours! It has steady and two flashing modes, and is housed in a water-resistant body.

- Plastic nylon molded body - Chromoly spindle - 318g pair

Put it on your handlebars, put it on your fork leg, put it anywhere—Sunlite's Griplite goes everywhere! This powerful little light has 2 LEDs and runs for a whopping 100 hours! It has steady and flashing modes and is housed in a water-resistant body.

• 2 bright Nichia LEDs • Uses 2 CR 2032 lithium batteries (included) • 100 hour run time • 3 modes: 2 flashing and 1 steady • Water-resistant silicone body

• 2 bright Red LEDs • Includes 2 (CR 2032) lithium batteries • 100 hour run time • 3 mode (2 flashing modes & steady mode) • Water resistant silicone body

Sunlite's HL-K100 Headlight is a great light at a great price. It sports a super-bright Krypton bulb housed in a tough, water-resistant body so it's perfect for commuting year round. A no-tools-required quick-release handlebar mount is included, too.

Dimension Junior Pedals. - Molded nylon, 1-piece, caged-type pedals - Built-in reflectors, will not accept toe clips - Overall pedal size is 80 x 60mm - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch or 1/2-inch - Pedal Type: Platform - Spindle Material: Chromoly Steel - Weight: 230g (9/16-inch); 304g (1/2-inch)

- High impact Resin multi-use body with integrated cage - Externally sealed ball bearing system - 100mm x 82mm platform - Weight: 316g pair (9/16")

Make sure you have excellent rear visibility at night with the Blinky 3. This sweet taillight aims 3 bright LEDs directionally to provide visibility from up to a mile away. Its soft-touch power switch accesses flashing or steady modes for up to 100 hours of run time on the 2 AAA batteries (included). And, it includes seatpost and seatstay mounts.

The Cascadia Fender Hardware Kits are compatible with Cascadia fenders, Hardcore fenders, and Full fenders. Includes: - Rear fender plastic clip - Fork and brake bridge-thru bolts - Stay bolts and lock washers - Disc adaptor spacers (60mm & 65mm widths only) Specific compatibility w/Planet Bike Fenders: - 35mm Width: 700c x 35mm Fenders (Cascadia & Hardcore) - 45mm Width: 700c x 45mm Fenders (Cascadia, Hardcore, and Full) - 60mm Width: 26-inch x 60mm Fenders (Cascadia & Hardcore) - 65mm Width: 29-inch x 65mm (Cascadia)

Long battery life combined with simple, tool-free mounting makes MSW Mouse lights a great economical pick to be seen on the road. - Simple, tool-free mounting on bars from 22.2 - 35mm - 3 lighting modes: high, low, flash - CR2032 battery included

- 32 lumen single LED safety light - 2 modes - steady and flashing - 2 CR2032 batteries included - Water resistant design

- 8 lumen, single LED safety light - 2 modes - solid and flashing - Up to 110 hour run time with 2 CR2032 batteries (included) - Multi-fit rubber strap attachment

Sunlite's 330 Taillight helps you be seen. It sports a 100 hour run time with a 1/2 watt 3 LED system. The housing is water resistant and it has steady and flashing modes.

Keep water and mud off you with SKS's Mud-X down tube fender! This versatile fender works with most bikes regardless of wheel size.

Addd an extra dose of stability to SKS's Velo 42 and Velo 47 fenders. A stainless steel U-stay mounts to the fenders and your frame eyelets to eliminate rattling and bouncing fenders.

- One-piece resin body and cage - Toe-clip compatible

- Guards against mud - Made from 100% recycled plastic waste - 100% recyclable - Supplied with 4 zip ties - Made in England

The S-Guard is not just for road bike cyclists; this super-lightweight (24g) and small mudguard protects your bottom from mud and water. Made with super-soft material, it fits on nearly every saddle with the addition of a cable tie.

- 20-lumen COB chip LED tail light - Powered by 2 AAA batteries (included) - Can be installed horizontally or vertically - IPX3 water-resistant rating

- Simplistic safety light combo pack designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - Both lights feature 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries each

- Single super bright LED safety light - USB rechargeable - cable included - Low battery indicator - Short 2.5-3 hour charge time with indicator light - Quick and easy to use silicone band attachment - 2 modes - Steady and flash - Lumens: 35

- Single super bright LED safety light - USB rechargeable - cable included - Low battery indicator - Short 2.5-3 hour charge time with indicator light - Quick and easy to use silicone band attachment - 2 modes - Steady and flash - Lumens: 8

- One-piece resin body - Chromoly spindle - Toe clip compatible - 366g pair

Small, compact, bright, quick and easy - there's no reason not to grab a pair of ORB's for your next ride. Features - Simple, lightweight, and compact design - Easy installation and switch operation - Universal rubber band - Battery type: CR2032 x2 - Mount size: ~22-32mm Modes/Run Time - Constant: 50 hours - Rapid flashing: 100 hours - Slow flashing: 100 hours

Small, compact, quick and easy - there's no reason not to grab a pair of ORB's for your next ride. Features - Simple, lightweight, and compact design - Easy installation and switch operation - Universal rubber band - Battery type: CR2032 x2 - Mount size: ~22-32mm Modes/Run Time - Constant: 50 hours - Rapid flashing: 100 hours - Slow flashing: 100 hours

A simple plastic fender that can be used on either the front or rear of the bike with styling to match your ride. - Available in multiple colors - Made in the USA

The TL 6.0 will help keep you safe and seen from behind (210-degree visibility). The TL 6.0 operates on 2 AAA batteries (included) for up to 60 hours on flash. Features - Lumen Output: 25 - 4 Modes with a Run Time up to 60h - 2 x AAA Alkaline Battery Powered - Weight: 70g - Battery: 2 x AAA Alkaline - Increased safety with 210° of Visibility - Budget Friendly Rear Lighting System - 25 Lumen taillight with Eye Catching Flash Patterns - Water / Dust Resistant IP64 Rated Run Time - Up to 60h

Planet Bike's Grunge Board is an easy-to-mount front fender that keeps you dry and clean when it's wet and muddy. It's made from a nearly indestructible polymer and it mounts in seconds to your down tube with the 2 rubber straps.

SKS's Cage Box offers light, simple storage for your on-the-go essentials. With enough room for your tools, mini pump, and a tube, the Cage Box slides easily into your water bottle cage for a rattle-free, easy access storage solution.

The Mudrocker Rear Extender can be snapped on and used for extra protection in the bottom bracket/derailleur area. This item is included with the Mudrocker Rear Fender, but we offer it here as a replacement. - Made in Germany

Easy to install and available in various colors and designs, the Splash Pad Front Fender won't let wet weather spoil your ride. It's designed for use with a range of bicycle styles and compatible with suspension forks. - A low-profile, easy-install fender that keeps riders clean in various conditions - Fits wide range of wheel sizes - Tool-free installation - Zip ties not included. Color zip tie options available through Problem Solvers.

Easy to install and available in various colors and designs, the MSW Splash Pad Rear Fender won't let wet weather spoil your ride. It's designed for use with a range of bicycle styles and is compatible with standard saddle rail configurations. - A low-profile, easy-install fender that keeps riders clean in various conditions - Fits wide range of wheel sizes - Tool-free installation - Zip ties not included. Color zip tie options available through Problem Solvers.

Simple solution to keep the spray down when the weather turns nasty - Attach to the fork crown and legs with zip ties - Compatibility: universal - Width: 120mm - Color: black - Weight: 20g

Others out on the roads and paths will see you when Sunlite's HL-L380 Headlight is on your bike. It sports 3 bright Nichia LEDs, steady and flashing modes, and 200 hours of run time! A quick-release handlebar mount is included, too.

- 2 super bright LEDs per light - Soft yet durable silicon casing - Never worry waterproof design - Universal rubber bracket

Lightweight and stealthy, Muc-Off Ride Guards keeps mud fling to a minimum. - Guards against mud - Made from 100% recycled plastic waste - 100% recyclable - Supplied with 4 zip ties - Made in England

Lightest and most versatile MTB mud guard available. - Uses hook and loop Velcro straps to attach to the bridge and lower legs - Compatible with forward and double bridge fork designs and all wheel sizes - XL version is longer and provides more coverage - Reverse version is designed for forks with reversed bridges - Fat Face Fender MV0035 updated to be compatible with FatBike suspension forks - Fat Face Fender XL, you guessed it, extra wide for FatBike applications

Odyssey Twisted PC pedals-extremely simple, lightweight, inexpensive and famously durable plastic-bodied design.Often duplicated but never replicated. - High-strength plastic composite

Meet the brand new, fantastic, feature packed Face Fender! Lightweight, discreet, and very effective, the Face Fender is a simple front mud guard for mountain bikes, made from 100% recycled plastic. SHIZZLE SHIELD - Integrated into the Face Fender is the Shizzle Shield, which, when folded toward the tyre, stops pretty much anything from being flung forward and hitting you in the mush. NO MORE ZIP-TIES - No more zip-ties! The fender is profiled to hold the Velcro fastener without needing zip-ties or anything else.

- One-piece ABS resin body - Molded pins - 320g pair

- One-piece nylon body - Chromoly spindle - Toe clip compatible - 407g pair

Super bright and compact, Cateye's Omni 3 Front Safety Light uses CatEye's Omni Directional Technology for increased visibility. Three super-bright LEDs light up in three different modes so you can customize the pattern and extend the run time. Plus, CatEye's tool-free FlexTight mount makes installation easy.

CatEye's Omni 5 Taillight uses Omni Directional Technology for 360 degrees of visibility. Five super-bright LEDs light up in three different modes so you can customize the pattern and get run times up to 120 hours. Plus, CatEye's tool-free mount makes installation a breeze.

- One-piece resin body - Juvenile size platform - Boron spindle - 390g pair

This flat-printed, origami-inspired polypropylene fender is ultralight, stylish, and quickly attaches and is ready to go when wet weather arrives. Simply remove from the package, punch out the shape and fold along the perforated lines. Reflective printing adds safety at night while multi-mount positions and hook-and-loop straps allows fender to fit a wide range of bikes. - Material: Polypropylene - Added Features: 3M reflective printing - Size: 31.7cm / 12.5" (in length) - Weight: 42g / 1.48oz

The Blinky Safety Light Set features a white headlight and a red taillight, both with super bright LEDs for top-notch visibility and safety. They also have flashing and steady modes providing 220 degrees of light that can be seen from up to 1 mile. Plus, these small flashers are weatherproof, light and durable. The included batteries deliver 100 hours of run time. And, handlebar, seatpost and seatstay mounts are included so they're super easy to put on your bike.

The Button Blinky Safety Set provides a quick way to keep you visible on your next bike ride. Two high output LEDs give you steady and flashing modes with 160° of visibility. These little lights are brilliant, easy to mount and cute as a button! Button Blinky front specs: - 2 high output surface mounted LEDs provide steady and flashing modes - FL1 Tested - Run times: 12 hrs (steady – 15 lm) and up to 40 hrs (flashing - 15 lm) - Provides 160° of visibility - One CR2032 battery (included) - Mounts with rubber stretch strap - 18 grams Button Blinky rear specs: - 2 high output surface mounted LEDs provide steady and flashing modes - FL1 Tested - Run times: 20 hrs (steady – 4 lm) and up to 50 hrs (flashing - 4 lm) - Provide 160° of visibility - One CR2032 battery (included) - Mounts with rubber stretch strap - 18 grams